Jump to content
Sign in to follow this  
Guest Black Tiger

GSM codes in depth

Recommended Posts

Guest Black Tiger

Iceke

Global User

(5/22/00 12:44:56 am)

GSM codes (in dept)

 

volgen hieronder

 

Iceke,

Iceke

Global User

(5/22/00 12:51:07 am)

Bosch 609 718 908 738 731 607

 

BOSCH CODES.

------------------------------------------------------

*#06# to display the IMEI

*#0000# to set the automaticly ( To english

*#3370# to set Enchaced to Full Rate

*#3370# to reset the phone

*#9000# to enter sim lock code

*#9003# to enter network code

*#9004# to enter the subset code

*#9100# to remove the sim lock permanently

*#9101# to remove the corporate lock permanently

*#9104# to remove the subset lock permanently

*#9102# to remove the provider lock permanently

*#9103 to remove the network lock permanently

 

These codes are Bosch com 609 com 718 com 908

Press *#3262255*8378# (equivalent to *#dancall*test#)

to make secret engineering menu (menu 10 ) appear.

Then you will be able to see the following info.

 

10. engineering

10.1 MS info

10.1.1 on

10.1.2 off

10.2 Software details

10.1.2 Software Version

10.2.2 EEPROM version

10.3 Test/production details

10.3.1 Hardware data

10.3.2 Production data

10.3.3 Service Data

 

 

--------------------------------------------------------------------

(SIM-lock is NOT the SP-lock/Service Provider lock!!)

The SIM-lock makes your phone to fusion with the SIM-card, and the phone will not

accept any other SIM cards after you lock your phone! You get ten chances to type

the correct code! After the tenth time your phone gets "SIM-lock permanently

blocked", and you will be unable to open it !! The best thing you can do is to remove

the SIM-lock permanently!!

NB. Tested on Bosch 738 phone and 607.

Thanks goes to Ernesto Bruscia and Bjørn Tore Nøstvold

--------------------------------------------------------------------

Bosch 608 PIN-OUTS UPDATED / NEW

Bosch bottom connector

______________

| 15 1 |

|( ) ======== |

|____16______2_|

16 GND Ground

15 EQUIP-ID Pulled low by HF, internal pullup 100k

14 AGND Analog ground

13 A-DL Analog output from phone

12 AGND Analog ground

11 A-UL Analog input to phone

10 GND Ground-this pin is checked by HF, if

GND=>phone is present

9 CHG-ID Charger ID - detects type of charger

8 D-BUS Data output

7 IGNITION Sensing ignition (in car kit),

internal pulldown 100k

6 HF_ENABLE HF enable output

5 V-BATT Connected directly to the MS battery. NO FUSE!

4 PA_BIAS_ON Trigger signal synchronous withr TX burst

3 I-BUS Data input (internal 100k pullup)

2 C-BUS Bi-directional serial control bus

1 VIN Input voltage - supply pin

 

Iceke,

Iceke

Global User

(5/22/00 12:53:59 am)

ALCATEL

 

ALCATEL

(pocket line series)

-------------------------------------------------------------------------

To view IMEI (International Mobile Equipment Identity) number enter *#06#

To Enter Service Menu enter: *#000000#

To view Secret Menu type 000000 then press *

-------------------

Secret Menu Appears

-------------------

TRACES channel indicator menus

ARRETS - ?

VIDER ARRETS Press OK and the phone responds: This action is executed!

CTRL CHARGE It show the charger voltage and battery voltage.

DAMIER display test

IMEI 3300 1453 1139 420

When activated with a Telstra card the Phone boots up with:

"PRODUCT CODE"

"VAL. => OK"

Then we enter 025121992 OK

"ENTER SPECIAL CODE"

**05* same as Motorola

"UNBLOCKING"

" PUK ? "

10608CC2*. These two from Vodaphone also work 906081C2* 15900807*

"UNBLOCKING"

" PIN ? "

0000*

"UNBLOCKING"

"PIN AGAIN "

0000#

 

Iceke,

Iceke

Global User

(5/22/00 12:55:31 am)

Philips

 

---------------------------

Philips Codes

---------------------------

Philips DIGA phones:

 

Blocking list *#3333*#

Time connected *#2558*#

Flags,something *#3377*#

Security code *#7489*#

 

Philips FIZZ phones:

 

IMEI code *#06#

SW info *#8377*#

Security code *#1234*#

 

Philips SPARK phones:

 

IMEI: *#06#

 

Philips GENIE phones:

 

*#06# IMEI number

*#2254*# Status register: C, BS, RR, MMI, CREAT.

*#2255*# activate and deactivate the "DEBUG CALL"-Mode; when activated, make

a call to a busy line an the phone will display some hex-codes on the display

*#2558*# the time in days,hours and minutes you are connected to the net

*#2562*# not clear; the phone reconnects to the net

*#2565*# not clear; warmstart

*#3333*# (NO) BLOCKING - list (15 items)

*#2377*# "BEER": not clear, the phone waits a random time and reconnects to the

net

*#3377*# Init, Flags, SIM LCK

*#3353*# resets the (NO) BLOCKING - list

*#7378*# Name, Length, SIM phase

*#7489*# SECURITY CODE

*#7693*# activate and deactivate the SLEEP MODE (when deactivated the battery

will go down!)

*#7787*# SPURIOUS INTERRUPT

*#7948*# SWITCH OFF

*#8463*# Some information about the SLEEP MODE: Wake, Sleep Req., Sleep

 

Pinouts for Philips Fizz and Spark

 

1 GROUND

2 GROUND

3 HANDS FREE ON/OFF

4 MUTE

5 TX

6 RX

7 RTS

8 REPROGRAMMING

9 ON HOOK CHARGER

10 AUX MIC

11 AUX SPEAKER

12 GROUND

 

 

Iceke,

Iceke

Global User

(5/22/00 12:56:54 am)

Siemens

 

------------

Siemens

------------

All Siemens phones:

SP unlock *#0003*(secret code 8 digits)#

 

Siemens S1 / S3

 

Show IMEI code: * # 06 #

 

Tetris: Power on phone and enter PIN. before phone has locked onto network, F9,

send own number, hit right button, hit 9. left is 2, right is 8, rotate is 5,

and drop is 4.

Monitor Mode: Menu, 9 (Phone Options), 7 (Phone Status), Left Display Button

(left MENU key), 5553756, HangUp Button (Red HandSet key)

Now "Monitor" should appear at the bottom of the Network Options menu.

Pressing the right Display Button when in monitor mode will show a list of the

six cells with the strongest signals.

Test Mode Indicators: (* = only available when call in progress )

 

CH Channel Number

RX Signal Strength (dB)

N NCC (Color Code)

B BCC (Color Code)

CI Cell ID (in Hex)

C1+ how long before phone does forced hand over. (see RX and RXAM)

LAI Location Area Identity. Display Network ID code (42F010 = 240.01)

and MSC

TXPWR Transmit Power (dB)

RXAM Receive signal strength cut-off point

TS* Time Slot Number

TA* Timing Advance. Distance from tower in Km X 2

PL* Power Level

 

Power Table

PL: 5 6 7 8 9 10 11 12 13 14 15

dB: 33 31 29 27 25 23 21 19 17 15 13

Watts: 2 1.3 .8 .5 .3 .2 .13 .08 .05 .03 .02

 

LF* C1 value with continuous transmission from tower

LS* C1 Value with discontinuous transmission from tower

QF* Bit Error Rate with continuous transmission from tower

QS* Bit Error Rate with discontinuous transmission from tower

 

BER (bit error rate) table

QF/QS register: 0 1 2 3 4 5 6 7

% of bit sent: 0.2 0.8 0.4 1.6 3.2 6.4 12.8 25.6

 

Siemens S3:comfort

 

Show IMEI code: * # 06 #

 

MONITOR MODE

The Siemens S3 Com series have a Monitor mode that can be activated directly

from the standard user keypad. In order to activate this mode, you must enter

the special access code currently programmed into the phone.

TO ACTIVATE MONITOR MODE:

Turn the phone on.

Enter the PIN access code on press OK. (Only if is enabled).

Press Menu. (Left top button).

Press 9. (Phone Options).

Press 8. (Phone Status) (May be button 7 in some phones).

You may see your IMEI Number

Left Display Button (Top left MENU key).

7684666

HangUp Button. (Red HandSet key).

Note: Monitor should appear now at the bottom of the Network Options menu.

MONITOR MODE TOGGLE

Pressing the right Display Button when in monitor mode will toggle into 1 and

2 modes

 

Siemens S4/S4 Power

 

Show IMEI code: * # 06 #

 

MONITOR MODE

The Siemens S4 series also have a Monitor mode that can be activated directly from

 

the standard user keypad. In order to activate this mode, you must enter the

special access code currently programmed into the phone.

TO ACTIVATE MONITOR MODE:

Menu, 9 (Phone Options), 7 (Phone Status), Left Display Button (left MENU key),

7684666, HangUp Button (Red HandSet key)

Now "Monitor" should appear at the bottom of the Network Options menu.

Pressing the right Display Button when in monitor mode will show a list of the

six cells with the strongest signals.

Test Mode Indicators: (* = only available when call in progress )

 

Siemens C 25

 

Show IMEI code: * # 06 #

Resets language to automatic selection : * # 0000 # then Green button

 

 

Pin Out

Data Cable schematics (click here)

Phone's connector pin-out:

 

1- GND

2- SB

3- POWER

4- NC

5- TX

6- RX

7- CLOCK

8- DATA

9- GND MIC

10- HF MIC

11- AUDIO

12- GND AUDIO

 

Iceke,

Iceke

Global User

(5/22/00 12:59:30 am)

Sagem

 

-------------------

Sagem

-------------------

Secret Codes

 

Type MENU - 5 - 1 - 1 - # to enter Engineering menu on SAGEM (RC-712 - 721)

phones.

 

Submenus:

1) IMEI

2) Flash Eeprom etc.

3) ?

4) SP unblock

5) ?

6) Contrast Settings.

 

When in menu type * and a new menu with new options will appear.

 

Sagem 612,615,715,725,730 Pin-Outs

 

 

1 8

[] --------

antenna --------

9 16

 

3 - TX

10 - RX

14 - GND

 

 

Iceke,

Iceke

Global User

(5/22/00 1:01:51 am)

Sony

 

-----------

Sony

-----------

Secret Codes

 

Sony CMD-Z 1

------------

To view IMEI (International Mobile Equipment Identity) number enter *#06#

Show Software version and manufact. date Following procedure will show on your

phone the software version in first row of the display and some CPU and OS info on

the second and third one.

# 8377466 # (#version#)

On earlier version the above tip may not work, but you can try this one:

In the menu go to PHONE SETTINGS Jog down to: FACTORY SETTINGS and CLICK

ONCE

You will see a display "Factory Setting Yes No" . Don’t do anything with this display,

leave it as it is.

move the main switch of the phone briefly to the right (briefly means long enough to

secure a short electric contact BUT short enough not to switch off the phone!)

Now you key in the following sequence:

# * 0 4

Will display info about sw (?)

 

Sony CMDX 1000

--------------

Show Software date Following procedure will show on your phone the software date.

 

Remove your SIM Card, then press:

* # 06 #

and finally press:

[left softkey]

To enter Monitor Mode on Network Option menu:

Menu

9 (Phone Options)

7 (Phone Status)

[Left Display Button] (left MENU key) 7684666 [HangUp Button] (Red HandSet key)

 

 

Software

--------

I have been asked a lot about how to update the software in Sony phones.

The easiest thing to do is to go to the nearest Sony

dealer and make him do it for you. Just remember that it is supposed to

be free (a receipt is needed) so don't let him tell you anything else!

 

Iceke,

Share this post


Link to post

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  




  • Hosting Fun

×
×
  • Create New...

Important Information

By clicking the accept button you specifically agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue. If you don't agree, please leave this site.