Jump to content

* * * Sinterklaas is weer in het land * * *


Piet schoorsteen Funboard Stoomboot

Sign in to follow this  
Guest theGIZMO

Humax IRCI5400 Allcam Patch v2.0

Recommended Posts

Guest theGIZMO

Een nieuwe patch van het Humfree-team is gereleased...ditmaal wordt de embedded Irdeto-CAM een All-CAM ! HIC 1.01.10ph V2.0 is de eerste versie die daadwerkelijk autoswithing ondersteund. Voor meer informatie/theorie achter het autoswitchen zie de bijgesloten Readme.txt.

Share this post


Link to post
Guest redneck eyeball

Gizmo,

 

Het is nochthans geen 1 april ... op de officiële site van Planet Hemp is daar niks over te vinden hoor. http://plahemp.da.ru/

 

Ook op http://www.satpage.de is niets te zien ...

 

Waar heb jij die gevonden ?

 

CU

Red

Share this post


Link to post
Guest redneck eyeball

Oeps, onderaan de pagina van planet hemp stond toch de link, is een beta versie ...

 

CU

Red

Share this post


Link to post
Guest redneck eyeball

En hier de vertaling van de readme :

(Met L&H software, dus vol fouten, maar beter dan niks)

 

== == == == HIC10110-+CAM -.HDF - version +CAM PH 2.0 == == == =

 

The V2.0, the first version participates, that a real Autoswitch

between different CA-IDs realized.

In contrast to the previous definition of " Autoswitch "

go the V1.7 far over this until now possible out:

On the basis of a solid eingespeicherten list of the most frequent

CA_IDs - 0602 1702 1722 and 1762 - supplements through the CA-IDs

this itself on the used card decides - seeks these

Firmware actively in the sent PM-Tabellen after one

Agreement. The Haupt-ID of the card is preferred with it

treat. Only when is found no agreement

can, comes the automatic case-mess table the carries. This

take care of it that also with lacking agreement

at least the Haupt-ID this in the PM-Tabelle was found

one appraises.

This completely new technology participates this from the SE-CI-CAM until now

used " Probiermethode " far thinks!

Through this technology, it possibly participates also cards without problems

, to use deviant CA-signals from the standard as well, for example

0605 or 0603. Until now also not yet used signals

will work without an Update of the firmware.

Since some Provider several signals for the same program

uses, some peculiarities nevertheless must heed

becomes: The defaulted rich-consequence of the to be used

CA-ID participates like follows:

1.) The main-signal of the used card

2.) 1702

3.) the sequence of this of ID within the sent PM -

Table.

 

Through this fixed sequence almost always participates

guaranteed, that EACH card co EACH signal EACH CA-ID

can process.

On the basis of some example shall the is clarified:

Card-signal 1762 - reception of a supplier with the signal

0602

In the PM-Tabelle, no agreement can with the 1762

is found, therefore function is entitled to the case-forecastle the carries.

Also the signal 1702 doesn't occur in the PM-Tabelle, therefore

another case-forecastle to the first signal within the PM -

Table. The card becomes consequently with the EMM/ECM Streamses of this

Signal 0602 looks after...

Card-signal 0602 - reception of a supplier with the signal

1702

In the PM-Tabelle, no agreement can with the 0602

is found, therefore function is entitled to the case-forecastle the carries.

One uses the 1702 and the card becomes with these EMM/ECMS

Streams looked after...

The absolute special cases - from the standard deviant CA-IDs -

become possible through this procedure first.

The only restriction exists with cards of Providern

this several CA-IDs within an encoding-system

uses. A card with the signal for example 1702 can under

becomes no circumstances on another signal of eingeloggt,

as long as these cards CA-ID in the sent PM-Tabelle

existing participates. As concrete example, ATV participates from the PW

Package quoted. Come in the PMT belonging to this canal

both 1702 as well as 1762 as signals before, so that always

the signal of the card uses becomes. At canals this only this

1762 as signal in the PM-Tabelle carry, ORF, can however

easily on the 1762 as signal is switched. Also

all other signals put with this Kartentyp no

Problem there, as long as the card-signal in the sent PM -

Table doesn't occur.

 

Friend problems:

 

Through the partially inert construction of the PM-Tabelle causes can

occurs that when switching between different

Providern with different CA-signals no one

usable data in the PM-Tabelle can be found.

Through renewed switching within the wished

Providerpaketes can this holding back in most however

Cases is remedied.

 

Avoiding Tunlichst essentially participates participate canals this no one.

The popular copyright-notes in the downloadbaren Settings

belongs to these " canals ". In most cases participates after it

no PMT evaluation more possible, so that only a complete

Latest-type of the Receivers remains.

 

Through the extensive Multitasking of the firmware and him/it

scarce Ramspeicher conditional stands it and at to a type

Hänger come, that however usually itself after some seconds

solve.

 

In very rare, not comprehensible cases, can it to

locks a complete the firmware comes, that only

through a hard Reset, appliance of the network separates, solved

can become.

 

Since only singularly the card-data with the start up of the appliance

completely from the Standby is read, should with one

Card-changes a latest-manner is executed. Becomes only so

guaranteed, that the new card-data for a possible

Autoupdate current participates.

 

Even if this clearly widened in the function-scope

Firmware the impression should awaken that the HumFree team

from his/its line " support only of Originalabos "

deviate, that doesn't participate the case! This firmware only pulls

on a tie as well from other side available

Hardware-solutions. Still becomes no definitely

Support for pirate-cards or emulators achieved!

 

Remain closed fun with the new firmware " only one " much

wishes.

 

Planet Hemp & HumFree team

Share this post


Link to post
Guest theGIZMO

Humax 5400 + HIC 1.01.10+ + DS9 = :-)))

Share this post


Link to post
Guest Mike The Bike

@ The Gizmo

 

Deze vette Smile betekent dat het werkt!?

 

Grtz Mike

Share this post


Link to post
Guest theGIZMO

@Mike The Bike,

 

Zeker weten...ik hoef niet meer uit m'n luie stoel te komen voor het betere zapwerk.

Share this post


Link to post
Guest Mike The Bike

Bij mij werkt 't dus duidelijk niet met de 401 versie, de 501-versie kan dit , volgens Wimpie, ook niet! What's the difference?

 

versie 401 (I.V.S.) + 16f628 en 24c65

 

Grtz Mike

Share this post


Link to post
Guest mr.hotbird

Het werkt met alle mosc kaarten ik hoef de kaarten niet meer te wisselen.

Zo blijft er meer tijd om mijn heerlijke biertje te drinken :)

Share this post


Link to post
Guest djazzie

snik :-( weer iets leuks in die hic 10 . en dat is juist net de soft versie waar ik . en mede stab interface gebruikers problemen mee hebben... jammer moet ik toch elke keer weer uit die luie stoel komen :-)

 

gr dj

Share this post


Link to post
Guest exDumber

En ik maar wachten pffffpffffpfffpfff op mijn kaartjes die ik besteld heb om van al dat moois te kunnen genieten :( :( :( :( :( :( :(

 

exDumber

Share this post


Link to post
Guest redneck eyeball

En ik met mijnen Goldprogger kan die nieuwe chips niet proggen. Ik zal mijnen Aston dus nog niet moeten wegdoen ... ;-)

 

CU

Red

Share this post


Link to post
Guest Happy2000

Ben hier ook even aan het stoeien geweest met de allcam patch en moet zeggen werk redelijk goed op een originele asc 1.2 c+ kaart beeld op ned - premiere - atv -bd zenders zonder de kaart eruit te halen (de rest zal ook wel werken maar nog niet getest).

Maar soms verslikt de softwarte zich dan geeft hij geen beeld met de aston had dit op de france zenders en op de nederlandse (had er toen geen irdeto kaart in).

Maar door even goed door te zappen springde hij weer aan.

(hij zag dus de kaart in de aston niet)

Al met al knap stukje werk en zullen de mensen die premiere niet op de humax aan de praaat kregen nu minder problemen ondervinden om dat het niet meer uit maakt wat voor type kaart je gebruikt.

Share this post


Link to post
Guest Stefaand

Ik heb deze versie er ook even ingezet, maar die is NIET autoswitch voor het DS9 project.

Trouwens....zit vol spellingsfouten.

Service is scramled or not runing ?

moet zijn

SCRAMBLED en RUNNING !!!

 

Stefaan

Share this post


Link to post
Guest Happy2000

HMMMM heb je wel de zelfde versie, hier zegt ie dan

bv : 0602 - This service want your money.

Share this post


Link to post
Guest Stefaand

Ja hoor ik heb dezelfde versie wnat hier zegt ie dat ook soms...en het moet ook zijn "wantS your money"...met een S.....zit vol taalfouten die versie!!!

Share this post


Link to post
Guest Mike The Bike

@Stefaand

 

Waarom beweer jij dat dit niet werkt met het DS9 project en theGIZMO wel?

 

Ik kan alleen de 501 versie niet proberen, maar de 401 versie loopt bij mij definitief niet! -> autoswitch niet, manual switch wel!

 

Grtz Mike

Share this post


Link to post
Guest theGIZMO

@Mike The Bike,

Even een correctie mbt DS9 na een dag hobbyen...regelmatig switch ie niet of het duurt meer dan een minuut ?! De hardwarematige reset oplossing, mbv de afstandsbediening, blijft toch een geschiktere oplossing.

 

@Stefaand,

Even aan de slag met een hex-editor om de taalfouten te verbeteren is niet zoveel werk.

Share this post


Link to post
Guest Stefaand

Manual switch werkt wel goed...maar ik dacht dat ik gelezen had dat die autoswitch was....helaas...

 

bedankt voor jullie reaktie.

 

Stefaan

Share this post


Link to post
Guest
This topic is now closed to further replies.
Sign in to follow this  




  • Hosting Fun

×
×
  • Create New...

Important Information

By clicking the accept button you specifically agree to our Terms of Use and Privacy Policy. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue. If you don't agree, please leave this site.